Huaxing PCBA production floor

Capabilities / PCBA Assembly / Through-Hole

Through-Hole Assembly,
Wave, Selective & Hand Soldering

When surface mount is not an option, high-power connectors, transformers, electrolytic capacitors, and legacy components, our through-hole lines deliver the mechanical strength and current capacity your design demands. Dual-wave, selective, and hand-soldering capabilities under one roof.

Dual-WaveWave Soldering
SelectiveNozzle Soldering
IPC 3Class 3 Available
IATF 16949
IPC-A-610 Class 3
ISO 9001:2015
100% Visual Inspection
Mixed-Technology

Choose the Right Process for Your Board

Wave Soldering

Dual-wave system for high-volume through-hole production. The first turbulent wave penetrates tight spaces and ensures full coverage; the second smooth (laminar) wave removes bridges and excess solder. Handles boards up to 510mm wide. Lead-free SAC305 as standard. Ideal for single-sided THT boards and mixed-technology boards where SMT components are glued on the bottom side. Typical throughput: 200-400 boards per hour depending on board size and component density.

Selective Soldering

Programmable nozzle-based soldering for mixed-technology boards where only specific through-hole sites need soldering: typically after all SMT components are already placed and reflowed on both sides. A micro-nozzle applies solder to individual joints under programmed X-Y control with preheat, flux, solder, and dwell time precisely calibrated per joint. Eliminates the need for pallets, masking, or glue. Ideal for high-density boards with a handful of THT connectors on otherwise fully SMT designs.

Hand Soldering

IPC-J-STD-001 certified technicians for prototypes, rework, and low-volume production. Temperature-controlled stations with cartridge tips for consistent thermal delivery. Used when automated processes are uneconomical (1-50 units), for rework of defective joints caught at AOI, or for unusually large components (bus bars, heavy-gauge wires, large transformers) that exceed wave or selective soldering capability. Each joint is visually inspected to IPC-A-610 criteria.

Primary Method

Dual-Wave Soldering Process

Wave soldering remains the workhorse of through-hole assembly. Our dual-wave system applies flux (spray or foam), preheats the board through three controlled zones, then passes it over two sequential solder waves. The turbulent first wave ensures solder reaches every lead in every hole, even on densely populated boards. The smooth second wave peels away excess, eliminating bridges and icicles.

  • Flux application, Precision spray fluxer with programmable pattern. No-clean and water-washable flux chemistries supported.
  • 3-zone preheat, Gradual ramp to 100-130°C (topside). Activates flux, drives off solvents, minimizes thermal shock to board and components.
  • Lead-free SAC305, Solder pot maintained at 260-270°C with automatic dross removal. Nitrogen blanket available for reduced dross and improved wetting.
  • Conveyor speed control, Programmable contact time (2-5 seconds typical) based on board thermal mass and component requirements.
Wave soldering production line

Precision Method

Selective Soldering for Mixed-Technology

Modern PCB designs are overwhelmingly surface-mount, but still need a few through-hole connectors, relays, or large capacitors. Selective soldering solves this by soldering only the through-hole sites on a board that's already fully SMT-assembled on both sides. No pallets, no masking tape, no glue, just a programmed nozzle that visits each joint.

  • Per-joint programming: Each solder site gets its own preheat time, flux volume, solder dwell, and withdrawal profile. Optimized for pin diameter, thermal mass, and proximity to SMT components.
  • No thermal stress on SMT, Only the targeted joint area reaches soldering temperature. Nearby SMT components stay well below reflow temperature, no risk of secondary reflow or component damage.
  • Ideal applications, RJ45 jacks, USB connectors, terminal blocks, electrolytic capacitors, relays, pin headers, and power connectors on otherwise fully SMT boards.
Through-hole component inspection and preparation

Through-Hole vs. SMT, Decision Guide

01

Mechanical Strength Required

Connectors subject to repeated mating force, heavy components subject to vibration, or anything that needs to survive mechanical shock. Through-hole pins anchored through the board provide far greater pull-out and shear strength than surface-mount pads. Common in automotive, industrial, and power electronics.

02

High Current / High Voltage

Power transistors, large electrolytic capacitors, bus bars, transformers, and high-current connectors often require through-hole for thermal management and current-carrying capacity. Plated through-holes provide lower resistance and better heat dissipation than surface-mount pad connections. Standard in power and energy applications.

03

Thermal Cycling Resilience

Through-hole solder joints form a full barrel fill, creating a 360° mechanical bond that resists the shear stress of repeated thermal cycling better than SMT fillets. Critical for under-hood automotive electronics, outdoor telecom equipment, and aerospace applications where temperature swings exceed 100°C in operation.

04

Legacy Component Availability

Some components, particularly high-power, high-voltage, and specialized connectors, are only available in through-hole packages. If your BOM includes DIP ICs, axial/radial passives, TO-220 transistors, or large pin headers, through-hole assembly is non-negotiable. We handle these seamlessly alongside SMT in a single production flow.

Through-Hole Assembly Specifications

ParameterWave SolderingSelective Soldering
Board WidthUp to 510mmUp to 510×460mm
Board Thickness0.8 – 3.2mm0.6 – 4.0mm
Solder AlloySAC305 (Pb-free), Sn63Pb37 (leaded)
Flux TypeNo-clean, water-washableNo-clean, rosin-based
Preheat Zones3-zone (top + bottom)Bottom-side IR + nozzle preheat
Min. Pin Diameter0.6mm0.4mm
Min. Pitch (PTH)2.0mm1.27mm
Max. Component Height (Bottom)15mm (pallet-dependent)30mm (clearance zone)
Throughput200-400 boards/hour3-10 joints/second
WorkmanshipIPC-A-610 Class 2/3, J-STD-001
Inspection100% visual + AOI where applicable
Component PrepLead forming, cropping, pre-tinning available

Need Through-Hole or Mixed-Technology Assembly?

Send your BOM and Gerber files. We'll evaluate the optimal soldering strategy, wave, selective, or hand, and return a complete quote with DFM recommendations within 24 hours.