Functional circuit test station for PCBA

Capabilities / PCBA Assembly / Functional Testing

Functional Testing,
FCT, ICT, Flying Probe, AOI, X-Ray

Comprehensive PCB and PCBA testing from bare board to powered-on functional verification. Seven test methodologies under one roof: every board that leaves our factory carries a digital test report. Custom fixtures designed and fabricated in-house. Test coverage: what you specify, we verify.

7Test Methods
100%AOI Coverage
CustomFixtures In-House
ReportPer Shipment
IATF 16949
IPC-A-610 Class 3
IPC Class 3 Medical
100% AOI + X-Ray on BGA
Full Test Reports

Catch Defects Before They Ship

FCT, Functional Test

Powered-on testing under real operating conditions. Custom test station built to your test specification, applies input signals, measures outputs, verifies firmware behavior. Simulates end-use environment: temperature, load, signal timing. Test fixture includes pogo-pin bed, power supply, signal generator, oscilloscope, and data acquisition. Firmware flashing and calibration included. Pass/fail criteria per your test plan. Full FCT report generated per board with serial number traceability.

ICT, In-Circuit Test

Bed-of-nails fixture with spring-loaded pogo pins contacts every test point on the board. Measures resistor values, capacitor values, inductor values, diode polarity, transistor gain, and open/short detection on every net, without powering the board. Catches wrong components, reversed polarity, missing parts, and solder opens before functional test. Fixtures designed and fabricated in-house. Typical ICT coverage: 85-95% of all components verified.

Flying Probe

Programmable moving probes contact test points without a dedicated fixture. Ideal for prototypes, low-volume production, and NPI where fixture cost is not justified. Four flying probes access both sides of the board simultaneously. Tests opens, shorts, component values, and diode/transistor orientation. No fixture cost and 24-hour programming turnaround. Limited to low-to-medium volume, ICT with fixture remains more economical above 500-1000 units.

3D AOI

Automated Optical Inspection on 100% of production boards. Koh Young Zenith 2 and Mirtec MV-6 systems capture 3D solder joint profiles from four angles at 25 micron resolution. AI-powered defect classification identifies bridging, tombstoning, lifted leads, missing components, wrong polarity, insufficient solder, and solder balls. Real-time SPC tracks defect trends across production lots. AOI is the first electrical-adjacent inspection gate, catching assembly defects before any powered test.

X-Ray, BGA/QFN

2D transmission X-ray on every BGA and QFN site, 100% coverage, not sample-based. Nikon XT V 160 and Nordson Dage Quadra 5 systems with automatic void analysis software. Void percentage calculated per ball against IPC-7095 thresholds. 3D computed tomography available for NPI qualification and Class 3 builds, reveals partial non-wets and head-in-pillow defects invisible in 2D. 0.5 micron feature detection resolves sub-micron cracks and intermetallic anomalies.

Burn-In Testing

Extended powered operation at elevated temperature (typically 50-70C) for 24-168 hours to accelerate infant mortality failures. Boards are powered and monitored in a temperature-controlled chamber. Catches marginal components, weak solder joints, and timing issues that pass initial functional test but fail within the first hours of operation. Common requirement for medical, aerospace, and automotive Tier-1 electronics where field failure is not an option. Burn-in profiles per customer specification or industry standard.

Optical Inspection

3D AOI: Every Board, Four Angles

Automated Optical Inspection is the universal gatekeeper in our production flow. After reflow soldering, every board passes through 3D AOI before it reaches any other test station. The system captures solder joint height, volume, and shape data from four camera angles. Not just a single top-down view that can miss lifted leads and hidden bridges.

  • 25 micron resolution, Resolves solder joint geometry at the level of individual grains. Detects wetting angle, fillet height, and pad coverage against IPC-A-610 class-specific thresholds.
  • AI defect classification, Machine learning model trained on millions of verified solder joints. Distinguishes true defects from acceptable process variation. Human operator reviews only borderline and rejected cases, not false positives.
  • Real-time SPC, Statistical process control tracks defect types and rates per product, per line, per shift. Early warning when a process starts to drift, before it produces scrap.
  • Full traceability: Every board's AOI result is stored with its unique serial number. Complete inspection history available for any shipped board.
3D Automated Optical Inspection system

Fixtureless Testing

Flying Probe, Rapid Test Without Tooling

When you need 5 prototypes tested tomorrow, not 500 units next month, flying probe is the answer. Four independently programmable probes move at high speed to contact test points on both sides of the board simultaneously. No custom fixture required: we program the probe paths from your CAD data (ODB++ or IPC-2581) and Gerber files, typically within 24 hours.

  • Zero fixture cost, No bed-of-nails to design, machine, and wire. Test program generated directly from your EDA output files. Ideal for prototypes, NPI runs, and products still undergoing design iteration where a fixed ICT fixture would be obsolete before it pays for itself.
  • Double-sided access, Probes access both top and bottom simultaneously. Measures component values, checks polarity, detects opens and shorts on every accessible net. Not as fast as ICT (seconds per board vs. fractions of a second) but eliminates the $2,000-$15,000 fixture cost.
  • Transition to ICT, When your volume justifies it, we design a bed-of-nails fixture and transition from flying probe to ICT. The flying probe test data serves as the golden reference for ICT program validation.
Flying probe test system for PCB testing

Test Flow by Production Stage

1

Pre-Reflow SPI

3D solder paste inspection. Verifies paste volume, area, height, and alignment on every pad. Catch stencil issues before placement.

2

Post-Reflow AOI

3D Automated Optical Inspection on 100% of boards. Solder joint quality, component presence, polarity, bridging, tombstoning.

3

X-Ray BGA/QFN

2D X-ray inspection on every BGA/QFN site. Void analysis per IPC-7095. 3D CT for NPI and Class 3 verification.

4

ICT / Flying Probe

In-circuit test or flying probe. Component value verification, open/short, polarity. Pass before powered test.

5

FCT

Functional circuit test, powered on, real operating conditions. Firmware flash, calibration. Per your test specification.

6

Burn-In (Opt.)

Extended powered testing at elevated temperature. 24-168 hours. Accelerates infant mortality. Medical, automotive, aerospace.

7

Final QA Release

Visual inspection, label check, packaging review. Digital test report compiled. Serial number traceability confirmed. Ship.

Test Capability Specifications

Test MethodWhat It VerifiesCoverageFixture RequiredBest For
SPIPaste volume, area, height, alignment100% padsNoAll production
3D AOISolder joints, components, polarity100% boardsNoAll production
X-Ray 2DBGA/QFN voids, bridges, missing balls100% BGA sitesNoAll BGA/QFN
X-Ray 3D/CTHead-in-pillow, partial non-wets, void distributionPer lot sampleNoNPI, Class 3
Flying ProbeComponent values, opens, shorts, polarity85-95% componentsNoProto, low volume
ICTComponent values, opens, shorts, polarity85-98% componentsYes, in-houseMid-high volume
Boundary Scan / JTAGInterconnects between JTAG devices, logic faultsJTAG-chain netsNoComplex digital
FCTPowered-on functional behaviorPer test specYes, in-housePer customer req.
Burn-InInfant mortality, marginal componentsPowered operationYes, in-houseMedical, auto, aero
Micro-SectionIMC layer, solder joint cross-sectionDestructive sampleNoNPI, failure analysis

Boundary Scan and JTAG

For complex digital boards with BGAs, fine-pitch connectors, and high layer counts where physical test point access is limited, boundary scan (IEEE 1149.1 JTAG) provides interconnect testing without physical probe access. We support boundary scan test development and execution for complex digital assemblies.

Interconnect Test

Verifies connections between all JTAG-compliant devices on the board, even nets buried under BGAs with no physical test points. Detects opens, shorts, and stuck-at faults on every pin of every device in the scan chain. Complements ICT for high-density digital boards where physical access is limited.

Memory Interface Test

Tests DDR memory buses between processors and DRAM, signal integrity, address and data line connectivity, and termination. Boundary scan patterns exercise the full memory interface at-speed. Detects marginal solder joints that pass DC continuity but fail under AC conditions.

Device Programming

In-system programming of flash memory, CPLDs, and FPGAs via JTAG chain. Firmware, serial numbers, MAC addresses, and security keys loaded during test. Eliminates pre-programmed device inventory management: every device is blank until test, ensuring version control.

Define Your Test Plan, We Build the Fixtures

Send your Gerber files, BOM, schematic, and test specification. Our test engineering team will propose the optimal mix of AOI, ICT, flying probe, X-ray, and FCT, with custom fixture design and fabrication included. Full test report with every shipment.